强力瓷砖背涂胶10L
Strong tile back coating adhesive is a high-performance anti stripping treatment agent and reinforcing agent with high bonding strength. Produced using unique emulsification technology, it has excellent adhesion and environmental protection characteristics, strengthening the bond strength between the pre treated base surface and the concrete mortar. This product has a certain elasticity coefficient, fully meeting the thermal expansion and contraction of tiles and stones, with good durability. It is a functional product that can solve the problem of delamination and brick falling of low water absorption vitrified tiles, marble, granite, etc.
Product Features
1.High adhesion and strong permeability;
2.High cost-effectiveness and easy to use;
3. Green and environmentally friendly, formaldehyde free and odorless.
Construction Technology
1.The base layer must be dry, clean, solid, and flat, without release agents, cement powder, oil stains, dust, and spilled mortar;
2. Mix the backing adhesive evenly first. Use a brush or roller to apply the backing adhesive to the back of the tile, let it dry for about 10-30 minutes until the surface is dry(the coating is transparent), and then use tile adhesive or cement mortar to lay it.
Precautions
1.To ensure product quality, the tile backing adhesive shall not be diluted with water or mixed with any other substances.
2.The recommended construction temperature is 5-35℃, and construction should be avoided in environments with rain,snow, frost, high temperature exposure, or large dust.
3.After opening, the product should be used up as soon as possible and kept out of reach of children.
4. When using this product, general labor protection equipment should be worn and the construction environment should bekept ventilated.
Storage and Transportation
1. Store in a cool and dry place, sealed and stored at a temperature of 5-35℃. Pay attention to antifreeze, moisture resistance,and exposure to sunlight.
2.This product is a non flammable, explosive, and corrosive material that can be transported as general cargo. During transportation, it should be protected from sunlight, frost, rain, compression, and collision, and the packaging should be kept intact and undamaged.
SHELFLIFE:12 months.
强力瓷砖背涂胶是一种具有高强粘结力的高性能防脱处理剂、增强剂。采用独特的乳化技术生产，既有优异的粘结性又具备环保特性，强化了预处理基面与混凝土砂浆的粘结强度。本品具有一定的弹性系数，完全满足瓷砖及石材的热胀冷缩，耐久性好，是一款能解决吸水率低的玻化砖、大理石、花岗岩等脱层、掉砖难题的功能性产品。
【产品特点】
1、高粘结度、渗透性强；
2、性价比高、使用方便；
3、绿色环保、无醛无味。
【施工工艺】
1、基层必须干燥清洁、结实平整，无脱模剂、水泥粉末、油渍、灰尘及溅落的灰浆；
2、口先将背胶搅拌均匀，用毛刷或滚筒将背胶涂刷在瓷砖背面，晾置10-30分钟左右至表干（涂膜成透明状态）时，即可用瓷砖胶或水泥砂浆铺贴。
【注意事项】
1、为保证产品质量,瓷砖背胶不得加水稀释及掺和其它任何物质。
2、施工温度建议在5-35℃避免在雨雪、霜冻、高温暴晒或灰尘较大的环境下施工。
3、开封后的产品需尽快用完,并置于儿童不易触及到的地方。
4、在使用本品时应佩戴一般劳动防护用品,施工环境保持通风。
【贮存与运输】
1、在阴凉干燥处密封储存，储存温度5-35℃注意防冻、防潮和暴晒；
2、本品为非易燃易爆易蚀材料，可按一般货物运输。运输中应防晒、防冻、防止雨淋、挤压、碰撞，保存包装完好无损。
【保存期】12个月。
